To dry towels, that is the main purpose of a heated towel rail and the benefit of a dry towel is less bacterial build up. We use only the best material, Grade 304 stainless steel, with it’s anti corrosion properties, prevents rusting, peeling chipping and staining. It is easy to clean, just use a warm , damp cloth, no detergent or chemicals necessary. A Cubic 6 bar heated towel rail uses only 70 watts of electricity.
Towel Holding Capacity: This model has the capacity to dry 2 x folded bath sheets.
Heated and Drying Times:
- Heated Towel Rail to Heat-Up: 10 – 15 mins
- To add a touch of warmth to a dry towel: 30 – 45 mins (when folded correctly in four layers)
- To dry an average used, damp towel: 4 – 5 hours (when folded correctly in four layers)
Estimated Running Cost: R56/month* (*Electricity costs calculated according to July 2020 COJ rates average cost R1.48/kwh. Based on running time 24/7 at 75% setting)
Built-In Controller: The discreetly built-in PTSelect (Personal Temperature Selection) Switch will enable you to switch the heated towel rail on and off as well as adjust the temperature to suite your personal heat preference.
Electrical Wiring: This electric towel rail is hardwired and the electrical connection must be completed by an electrician. This product has a Dual-Entry electrical connection which means it has both LEFT and RIGHT electrical connections, and can be connected to any of the two sides straight out of the box to better suit your electrical point.
Material: Grade 304 Stainless Steel
Stainless Steel has a natural resistance to corrosion and therefore does not require a protective coating which makes this product ideal for the bathroom environment. The shiny polished Stainless Steel finish is often confused with a Chrome finish, however the two could not be more different. While stainless steel will not peel or flake, chrome products on the other hand are susceptible to chipping and pitting due to the nature of a coated surface.
What’s in the box:
Heated Towel Rail
Mounting kit which includes masonry wall fasteners [Fischer UX 6mm Plastic Plugs and Screws (2 pieces), Fischer UX 8mm Plastic Plugs and Screws (3 pieces)]
Installation Instructions (1 piece)
Mounting template (1 piece)
Tools needed (not supplied):
Drill & Drill bits
- 6mm and 8mm Diamond drill bit – if drilling through Ceramic tiles
- 6mm and 8mm Masonry drill bit – if drilling into Masonry (Brick)
Measuring tape
Pencil
PH2 screwdriver
Spirit level
Installation Tip:
- Check for water pipes before drilling
- In Masonry walls, always drill a smaller pilot hole first for better accuracy regarding location and sizing
Cleaning & Care: Stainless Steel finishes
It is important to regularly clean your Bathroom Butler products to keep them in pristine condition. Simply wipe it down with a warm damp cloth and then buff dry with a clean dry microfiber cloth. You could also, on occasion use a Chlorine-free stainless steel cleaner to maintain the shine. If you use stainless steel polish, make sure it is abrasive-free.
When cleaning wall or counter surfaces around your product do not use any household detergents that may contain Chlorine based chemicals such as bleach as it will cause permanent damage to the surface of the stainless steel.Take special care with all colour finishes.
DO NOTuse the rough end of a kitchen sponge to clean your product.
DO NOTclean your product with any kind of ACID BASED CHEMICAL, TILE CLEANER, or detergents that contain CHLORINE. This may contaminate and damage the surface finish of the product.
Heated Towel Rails Specs:
Model: CUB06221-PTS
Size: 553 mm (width) x 755 mm (height) x 107 mm (depth)
Power: 70 Watts
Current: 0.30 Amps
Volts: 230 VAC
IP Rating: IPX5
Material: GRADE 304 Stainless Steel
Time Needed for Heated Towel Rail to Reach Optimum Temperature: 10 - 15 mins
Time Needed to add a touch of warmth to dry towels: 30 -40 mins (when folded correctly in four layers)
Time Needed to dry an average used damp towel: 4 – 5 hours (when folded correctly in four layers)
Suggested Height of Electrical Outlet = 1050mm (this is only an indication as every installation is different)
Standard Finishes Available: POLISHED Grade 304 Stainless Steel / MATT Black
Controller Specs:
Controller: PTSelect Switch
Features: Temperature Adjustment + ON / OFF Switch + RED LED Indicator
INPUT Voltage Range: 190VAC~250VAC
Operating Frequency: 50 Hz ±2%
Load Capability: 0.18A~4A
Load Control Range: 40~100%
Standby Current: 3.0mA
